Plumbing Basics: What You Need for Bathtub Installation

Call Today

We've uncovered this great article relating to How to Install a Bathtub listed below on the web and believe it made perfect sense to write about it with you on this page.

Setting up a bathtub isn't specifically rocket science, but it does require solid plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately hard job. If the old tub is conveniently easily accessible, the project can relocate rapidly; if you have to open up a wall to eliminate the old tub as well as place the brand-new tub, the task is a lot harder. In either instance, the project is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub and embeded in the brand-new one. Make sure you have actually qualified yourself for the task and fit attempting it. Instead of working with a specialist to take over a halfway-completed task, it is better to think about utilizing one prior to you begin. Possibilities are you may require a professional plumber to make tube connections.
This write-up will certainly aid you set up a new bathtub in your restroom if you have actually already purchased a brand-new tub and don't need to change the plan of your previous water supply pipelines.
Your tools and also product checklist ought to comprise the following:

New Bathtub

Hammer

Pipe Wrenches

Prybar

Safety Glasses

Level

Pliers

Flexible Wrench

Putty Blade

Screwdriver

Cold Knife

Tape Measure

Pipe Caps

Planning for the Setup

To start with, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to ensure that if the faucet features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps making use of 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its final position.

Removing Old Taps

If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite bothersome due to the limited accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will originate from the pipes. As soon as the supply pipes have been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

Installing the Bathtub

Using both wood boards under its feet, position the bathtub in the required position. The wooden boards are handy in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four tiny points.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level and readjusting the feet on the bath tub up until the spirit level reviews degree.
To set up faucets, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply as well as check all joints and also brand-new pipework for leakages as well as tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet and the regular outlet for leaks.
Ultimately, take care of the bath paneling as defined in the supplier's user's manual. Tiling and sealing around the bath tub needs to wait until the bathtub has actually been used at the very least when as this will settle it right into its last position.

Fitting New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and the other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin ensuring that the washing machines are in place in between the tap as well as the sink. Secure the faucet in position with the maker given backnut. When the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical faucet connectors. The former kind ought to be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.

Tiling Around the Bath tub

In the location where the bath fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to split a rigid seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, resulting in difficulties with dampness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your components as well as installations. They are sold in tubes and cartridges, and also can securing voids up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bath tub with water before securing, to permit the movement experienced when the tub is in usage. The sealant can fracture fairly early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily offered on the market. It is advisable to fit the tiles using water-resistant or waterproof adhesive as well as cement.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Do you like reading up on A Step-by-Step Guide to Installing a Bathtub? Try leaving feedback directly below. We would be glad to listen to your reactions about this write-up. We hope to see you back again soon. For those who liked our blog post please do not forget to pass it around. Bless you for your time. Come back soon.

Protect your space!